CUMMINS VCP 7.7 VEPS software was created to support 2010 Cummins engines plus new parameters for Euro 5 engines and ISZ CM2150E

This version of the VEPS software was created to support 2010 Cummins engines plus new parameters for Euro 5 engines and ISZ CM2150E.

New in Version 7.7

Starting with this release, VEPS will automatically upgrade previous installations to the latest version. It is no longer necessary to unistall an existing installation of VEPS before installing VEPS 7.70 or later versions.

2007 ECMs:

New Engine programs supported:

CM2250(BBN,BBO,BBP,BBZ) and CM2150E(BAM)

New features:

MR-2010(CM2250) HDD-2010(CM2250) MR-Euro5(CM2150E) HDD-ISZ(CM2150E)

- 50037 - Switched Maximum Vehicle Speed Y Y

- 50038 - Switched Maximum Road Speed Setting Y Y

- 50040 - Variable Rate Vehicle Acceleration Management Y Y Y Y

- 50041 - Variable Acceleration 1 Y Y Y Y

- 50042 - Variable Acceleration 2 Y Y Y Y

- 50043 - Variable Acceleration Speed 1 Y Y Y Y

- 50044 - Variable Acceleration Speed 2 Y Y Y Y

- 50045 - Urea Tank Heater 1 Relay Y Y Y

- 50046 - Linear Urea Tank Volume Y Y Y

- 50047 - Urea Tank Type Y Y Y

- 500481 - Non Linear Urea Tank Level X 1 Y Y Y

- 500482 - Non Linear Urea Tank Level X 2 Y Y Y

- 500483 - Non Linear Urea Tank Level X 3 Y Y Y

- 500484 - Non Linear Urea Tank Level X 4 Y Y Y

- 500485 - Non Linear Urea Tank Level X 5 Y Y Y

- 500486 - Non Linear Urea Tank Level X 6 Y Y Y

- 500487 - Non Linear Urea Tank Level X 7 Y Y Y

- 500488 - Non Linear Urea Tank Level X 8 Y Y Y

- 500489 - Non Linear Urea Tank Level X 9 Y Y Y

- 5004810 - Non Linear Urea Tank Level X 10 Y Y Y

- 5004811 - Non Linear Urea Tank Level X 11 Y Y Y

- 500491 - Non Linear Urea Tank Volume Y 1 Y Y Y Y Y

- 500492 - Non Linear Urea Tank Volume Y 2 Y Y Y

- 500493 - Non Linear Urea Tank Volume Y 3 Y Y Y

- 500494 - Non Linear Urea Tank Volume Y 4 Y Y Y

- 500495 - Non Linear Urea Tank Volume Y 5 Y Y Y

- 500496 - Non Linear Urea Tank Volume Y 6 Y Y Y

- 500497 - Non Linear Urea Tank Volume Y 7 Y Y Y

- 500498 - Non Linear Urea Tank Volume Y 8 Y Y Y

- 500499 - Non Linear Urea Tank Volume Y 9 Y Y Y

- 5004910 - Non Linear Urea Tank Volume Y 10 Y Y Y

- 5004911 - Non Linear Urea Tank Volume Y 11 Y Y Y

- 50050 - Urea Tank Heater 2 Relay Y Y Y

- 50051 - Urea Line Heater 1 Relay Y Y Y

- 50052 - Urea Line Heater 2 Relay Y Y Y

- 50053 - Enhanced Auxiliary Shutdown Switch Y Y Y

- 50054 - Enhanced Auxiliary Shutdown Switch Logic Y Y Y

- 50055 - Enhanced Multiplexed Auxiliary Shutdown Switch Y Y Y

- 50056 - Enhanced Auxiliary Shutdown Switch Multiplexed Y Y Y

Address

- 50057 - Idle Shutdown Service Brake Switch Y Y

- 50061 - Regeneration with Parking Brake Y

- 24011 - Immobilizer

- 50029 - Kickdown Pedal Smart Road Speed Governor

- 50030 - Smart Road Speed Governor 2 Y Y Y Y

- 50016 - Load Based Speed Control - Enhanced Y Y Y

- 50027 - Low Engine Speed Breakpoint - Enhanced Y Y Y

- 50028 - High Engine Speed Breakpoint - Enhanced Y Y Y

Bug fixes:

- 25771 - Dual Accelerator Pedal Enable, didn't work correctly with its related user selectable. fixed.

_________________________________________________________________________________________________________

CUMMINS VCP 7.6

This revision of the VEPS software was created to support European Level5 emissions applications. It also added three new parameters described below.

New in version 7.6

2007 ECMs:

New Engine programs supported:

ISBe Euro 4.5/5, ISLe Euro 4.5/5

New feattures:

- 50005 - Parking Brake Switch

- 50018 - Oil Level Electronic Dipstick Engine Power Angle

- 50019 - Oil level Electronic Dipstick Horizontal Engine Tilt Angle

- 50017 - Oil Level Electronic Dipstick Oil Pan Type

- 50021 - Oil Level Electronic Dipstick Oil Pan Port Location

- 50022 - Oil Level Sensor Enhanced

- 50029 - Smart RSG Extension Kickdown Pedal

- 50030 - Smart Road Speed Governor 2

- 50023 - Cruise Control without Parking Brake Set

- 50025 - PTO with Parking Brake Set

- 24011 - Immobilizer

For both Euro4.5/5 and 07 engines

- 50026 - Fan on With Remote Throttle

- 15181 - Switched Maximum Engine Operating Speed Enable

- 15182 - Maximum Switched Engine Speed

Bug fixes:

- Common Components have been updated to version 1.12.3 to fix communication error when using NEXIQ and DearBorn data link adapters to communication with Cummins ECM

- updated DE0201.dll for 04 Engines (ISC 03, ISL03, ISM 02, ISX 02 and ISM 04) to fix communication failure error when using 7.53

- 23002 - Isochronous Breakpoint Speed. The parameter used to be named as "Maximum Switched Engine Speed", which refers to a different parameter in InSite

Pre 2007 ECMs:

not changed

______________________________________________________________________________________________________

New in Version 7.53

2007 ECMs:

New features:

- Passwords: Adjustment and Reset can be '000000' (default disabled password value) if Master is also '000000'

- Passwords: All passwords can be 1-6 in length. It will be padded to with 0x00s to the right. Example - ['M']['M'] --> ['M']['M'][0x00][0x00][0x00][0x00]

- 12300 has been added to the documentation file. This was not included in previous documents, but was supported in the software.

- Grid Heater Enable (30500) is now supported in VEPS for 2007 engines, where the calibrations also support it.

- All the Min/Max ranges and default values have been removed from 2007 engine documentation released with VEPS. This is to avoid confusion when a new calibration is released and VEPS documentation is out of date. Please consult the GCE website which has updated calibration documentation for the latest values.

Bug fixes:

- 15460 has been removed from VEPS support. Parking Brake PTO Enable is not a valid parameter.

Pre 2007 ECMs:

- CM800 Euro3 and CM850 Euro4 - Added support for Load Based Speed Control (10040)

- CM850 Euro4.5 - Added support for the following parameters

12000 - Oil Level Electronic Dipstick

12001 - Oil Level Electronic Dipstick Engine Power Angle

12002 - Oil Level Electronic Dipstick Engine Min Power Angle

12003 - Oil Level Electronic Dipstick Engine Max Power Angle

12011 - Oil Level Electronic Dipstick Oil Pan Type

12012 - Oil Level Electronic Dipstick Oil Pan Location

12031 - Oil Level Electronic Dipstick Horizontal Engine Tilt Angle

12032 - Oil Level Electronic Dipstick Min Tilt Angle

12033 - Oil Level Electronic Dipstick Max Tilt Angle

12100 - Intake Air Heater

_____________________________________________________________________________________________________

New in Version 7.52

2007 ECMs:

New features:

- Added new parameters 30090 Coolant Level Configuration and 30190 Coolant Level Mux Address.

- Added support for unlocking and changing 2007 OEM Password.

- Allow for same Par file to be used again even when setting core2 Master Password or OEM Password.

Bug fixes:

- (11440) bug: If (10000) = (11440) = (11430), when 10000 is lowered and 11440 is in the par file and not set below 10000 along with 11430, then VEPS errors out. This is fixed so that 11440 and 11430 are moved to 10000's value if they are in the par file and a warning is given for each.

- When the latest version of the Cummins engineering tool was installed on the same PC as the VCP software, Multiplexing values were not written to the ECM by the VCP software due to a newer version of a shared library installed on the PC. This issue has been resolved so that regardless of the version of the shared library, the Multiplexing values will be registered in the ECM.

- Display name for Battery Voltage Monitor changed to Alternator Failure Warning to match INSITE naming convention.

Range fixes:

- The Max value for (30311) is the difference of (13590) and (10090).

- Corrected max value for TI_MPH_Overspeed_1 (12940) and TI_MPH_Overspeed_2 (12950) from 16383.8 to 10180.4 m/h.

Pre 2007 ECMs:

- CM800 Echo modules would at times not send all the bytes in the feature table (AENBLFLG) to the VCP software. Checks have been added to make sure this does get read. If it doesn't after 6 tries then it will error out. If all goes well, this adds less than 4 seconds to the full programming of a pre-2007 ECM.

_____________________________________________________________________________________________________

New in Version 7.51

This revision of the VEPS software was created to support:

The 2007 Automotive products: ISB, ISC, ISL, ISM, ISX 07.

The main focus of this release is to add support for the new Aftertreatment features and parameters. Also, there have been parameters that have been added that were missed in previous releases.

The following parameters were added to the VEPS software:

11090 PTO Device 1

11091 PTO Device 2

11092 PTO Device 3

11093 PTO Device 4

11094 PTO Device 5

11095 PTO Device 6

11096 PTO Device 7

11097 PTO Device 8

12940 Vehicle Overspeed 1

12950 Vehicle Overspeed 2

14560 Fast Idle Warmup PTO Load Threshold

14570 Fast Idle Warmup Idle Speed

15180 Maximum Operating Speed Switch Setup

15432 Idle Shutdown with Parking Brake ON

15434 Engine Brake Lamp

15460 PTO with Parking Brake ON

22571 Battery Voltage Monitor

22581 Battery Voltage Monitor Idle Speedup

23002 Maximum Switched Engine Speed

23121 Switched Droop Enable

24051 Vehicle Acceleration Management

25281 Fast Idle Warmup

25571 OEM Temperature Input Enable

25581 OEM Pressure Input Enable

25771 Dual Accelerator Pedal Enable

27021 J1939 Trip Reset

27031 J1939 Service Reset

27041 J1939 Stop Broadcast Allowed

30077 Diesel Particulate Filter Regeneration Start Switch

30078 Multiplexed Aftertreatment Regeneration Start Switch

30087 Diesel Particulate Filter Regeneration Permit Switch

30088 Multiplexed Aftertreatment Regeneration Permit Switch

30097 Automatic Stationary DPF Regeneration

30107 DPF Regeneration in PTO

30117 DPF Regeneration Lamp

30178 Aftertreatment SRegen Switch Multiplexed Address

30188 Aftertreatment Permit Regen Switch Multiplexed Address

30207 Aftertreatment HEST Lamp Setup

30208 HEST Lamp Setup When Regen In Progress

30211 HEST Lamp Setup Vehicle Speed

30212 HEST Lamp Setup Low Threshold

30213 HEST Lamp Setup High Threshold

30307 Driver Initiated Override

30311 Driver Initiated Override Max Road Speed Delta

30312 Driver Initiated Override Max Distance

99000 Fuel Log Enable

99002 Trip Information Vehicle Enable

199251 Acceleration Rate

_____________________________________________________________________________________________________

New in Version 7.5

This revision of the VEPS software was created to support:

the 2007 ISB & ISC/ISL programs;

additional parameters in the Tier3 Core 2 programs and the Echo program;

Adjustment and Reset passwords and Engine Serial Number for Core 2 Automotive programs;

and some performance and error handling issues in past releases.

New Engine programs supported:

- 2007 ISB & ISC/ISL programs.

Changes For all Engine Programs

- None

Verification File Change

- None

ISM 07 ISX 07

- Added support for setting Adjustment (00024) and Reset (00021) Passwords

- Added support for Setting Engine Serial Number (3003)

- Added additional Fan Clutch Type Options (12490)

ISB 07

- All parameters supported in ISM/ISX 07 are supported in ISB 07 (unless the specific calibration does not)

- Added support for setting Adjustment (00024) and Reset (00021) Passwords

- Added support for Setting Engine Serial Number (3003)

- Added additional Fan Clutch Type Options (12490)

ISC 07 ISL 07

- All parameters supported in ISM/ISX 07 are supported in ISC/ISL 07 (unless the specific calibration does not)

- Added support for setting Adjustment (00024) and Reset (00021) Passwords

- Added support for Setting Engine Serial Number (3003)

- Added additional Fan Clutch Type Options (12490)

ISBe4 ISLe4 ISMe4

- None

QSB QSC QSL (Tier III)

- Added support for 10050, 10060, 10070

All EGR Engine Programs

- None

ISM 02 ISX 02

- None

ISB 02 ISC 03 ISL 03

- None

ISBe

- Added support for 15460 and 21251.

ISC / ISL

- None

Natural Gas Engines

- None

QSB / QSC

- None

Heavy Duty

- None

Known Issues

- None

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, L10G+, Signature 600, ISB 02, ISC 03, ISL 03, ISX 02, ISM 02, ISM 04, ISB 07, ISC 07, ISL 07, ISM 07 and ISX 07 engines.

_____________________________________________________________________________________________________

New in Version 7.4

This revision of the VEPS software was created to support the remaining parameters of the 2007 ISM/ISX program.

New Engine programs supported:

- None

Changes For all Engine Programs

- Each execution of VEPS will now create a comma separated value text file of the VEPS report. By default the file will be named “ceco600.vrp”. Use the “-r” to specify the report file name.

Verification File Change

- None

ISM 07 ISX 07

- Added support for the complete set of adjustable parameters. See the document "ISM ISX 07 Programmers Reference manual" for a complete list of parameters.

ISBe4 ISLe4 ISMe4

- Corrected the software version check that was preventing the support of some Euro 4 parameters.

QSB QSC QSL (Tier III)

- Added support for 10000, Maximum Accelerator Vehicle Speed.

- Corrected a bug that prevented the user from changing 40200, 40210 and 40220.

All EGR Engine Programs

- Added support for 15432, Idle Shutdown with Parking Brake ON.

- Removed the requirement that 15460, PTO with Parking Brake ON be multiplexed.

- Removed the requirement that 20011 (PTO) be enabled before programming PTO parameters. This allows customers to setup PTO without turning it on.

- Added support for 27021, J1939 Trip Reset.

- Added support for 27031, J1939 Service Reset.

- Added support for 27041, J1939 Stop Broadcast Allowed.

ISM 02 ISX 02

ISB 02 ISC 03 ISL 03

ISBe

ISC / ISL

Natural Gas Engines

QSB / QSC

Heavy Duty

- None

Known Issues

- None

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, L10G+, Signature 600, ISB 02, ISC 03, ISL 03, ISX 02, ISM 02, ISM 04, ISM 07 and ISX 07 engines.

_____________________________________________________________________________________________________

New in Version 7.33

This revision of the VEPS software was created to fix Write Verification Errors reported by the field.

Changes For all Engine Programs

- If any Write Error occurs, attempt to write the value one more time before reporting an error.

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, L10G+, Signature 600, ISB 02, ISC 03, ISL 03,ISX 02, ISM 02, ISM 04, ISM 07 and ISX 07 engines.

_____________________________________________________________________________________________________

New in Version 7.32

This revision of the VEPS software was created to fix Write Verification Errors reported by the field.

Changes For all Engine Programs

- If a Write Verification Error occurs, attempt to write the value one more time before reporting the error.

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, L10G+, Signature 600, ISB 02, ISC 03, ISL 03,ISX 02, ISM 02, ISM 04, ISM 07 and ISX 07 engines.

_____________________________________________________________________________________________________

New in Version 7.3

This revision of the VEPS software was created to support Heavy Duty (ISM/ISM) 2007 applications. This release supports a subset of the complete list of 2007 parameters. The rest will be supported in the next release.

New Engine programs supported:

- ISM / ISX 07 (No J1708/J1587 support, MUST be programmed via J1939)

Verification File Change

- Error 0955 - The value being assigned this parameter is not defined as a valid setting in this calibration.

ISM07 ISX 07 (Only programmable via J1939)

- 30000 is no longer required or supported

- 30008-30034 Have changed from Y/N enables to accepting values 0, 128-133. Use 128 for standard J1939 Multiplexing.

Added support for the following parameters:

1001 - OEM Name

1003 - OEM Vehicle or Equipment Model

1005 - VIN or equipment serial number

1006 - Vehicle or equipment year

1009 - Customer name

1010 - Customer location

1011 - Customer unit number

10000 - Maximum Accelerator Vehicle Speed

10020 - Maximum Engine Speed Without VSS

10030 - Low Idle Speed

10050 - Rear Axle Ratio

10060 - Tire size

10070 - Tailshaft Teeth

10080 - VSS Type

10090 - Maximum Cruise Control Speed

10100 - Set/Resume Switch Usage

10130 - PTO Maximum Speed

10170 - Idle Shutdown Timer

10300 - Top Gear Ratio

10790 - Clutch Switch

11340 - Gear Down Gear Ratio

11390 - PTO Minimum Speed

11410 - Transmission Type

11540 - Engine Brake Minimum Vehicle Speed

12490 - Fan Type

12780 - Fan Clutch Logic

12790 - Driveline Brake Type

13590 - Maximum Vehicle Speed

20001 - Low Idle Speed Switch

20011 - PTO

20021 - Cruise Control

20051 - Idle Shutdown

20071 - Idle Shutdown in PTO

20081 - Idle Shutdown Manual Override

20571 - Coolant Level Sensor

21461 - Fan Control Switch

21712 - Air Conditioning Pressure Switch Input

22221 - Fan Control

23021 - Engine Brakes

30008 - Multiplexed Service Brake Switch

30010 - Multiplexed Clutch Pedal Position Switch

30012 - Multiplexed Cruise Control On/Off Switch

30014 - Multiplexed Cruise Control Set Switch

30016 - Multiplexed Cruise Control Resume Switch

30018 - Multiplexed PTO On/Off Switch

30020 - Multiplexed PTO Set Switch

30022 - Multiplexed PTO Resume Switch

30034 - Multiplexed Fan Control Switch

30106 - Service Brake Switch Multiplexed Address

30108 - Clutch Pedal Position Switch Multiplexed Address

30110 - Cruise Control On/Off Switch Multiplexed Address

30112 - Cruise Control Set Switch Multiplexed Address

30114 - Cruise Control Resume Switch Multiplexed Address

30116 - PTO On/Off Switch Multiplexed Address

30118 - PTO Set Switch Multiplexed Address

30120 - PTO Resume Switch Multiplexed Address

30132 - Fan Control Switch Multiplexed Address

40220 - Remote Accelerator Mode

ISBe4 / ISLe4 / ISMe4

21701 – Adaptive Cruise Control Enable

11712 – Adaptive Cruise Control Recovery

Known Issues

11540 - Engine Brake Minimum Vehicle Speed reports that is successfully programmed, but when checked, it hasn’t changed.

10090 - Maximum Cruise Control Speed, the tool upper limit defined in the latest released calibration is 0, so VEPS will automatically set 10090 to 0.

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, L10G+, Signature 600, ISB 02, ISC 03, ISL 03,ISX 02, ISM 02, ISM 04, ISM 07 and ISX 07 engines.

_____________________________________________________________________________________________________

New in Version 7.2

This revision of the VEPS software was created to support European Level 4 emissions applications. It also contains minor revisions to three parameters described below.

All EGR Engine Programs

- Added support for 15320 – Vehicle Speed Signal Tampering Sensitivity Level.

ISC / ISL

- Added support for 21221 - Accelerator Interlock.

Heavy Duty

- Removed the requirement that said 12479 – Top 2 Enable must be ENABLED for 11410 – Transmission Type to be set to option 3 – Partially Automated.

ISBe4 / ISLe4 / ISMe4

- Added support for European Level 4 emissions applications:

15500 – Euro Smart Road Speed Governor

23241 – Switched Speed Road Speed Governor

14240 – Maximum Secondary Vehicle Speed without Cruise Control Active

25791 – Acceleration Rate Variable Limit

15421 – Acceleration Rate Speed 1

15422 – Acceleration Rate Speed 1 Rate Limit

15423 – Acceleration Rate Speed 2

15424 – Acceleration Rate Speed 2 Rate Limit

15430 – Idle Shutdown Coolant Temperature

15431 – Idle Shutdown Coolant Temperature Value

25201 – Cruise Control with Parking Brake OFF

15460 – PTO with Parking Brake ON

25771 – Dual Accelerator Pedal

20591 – Vehicle Electrical System Voltage

24011 – Immobilizer

15480 – Maximum Engine Speed Droop Option

15212 – Real Time Clock

15470 – Real Time Clock From Datalink

15471 – Real Time Clock From Datalink Source Address

25781 – Urea Heater

25801 – Non-Linear Urea Tank Type

15510 – Linear Urea Tank Volume

15520 – OEM Volume Input 1

15521 – OEM Volume Input 2

15522 – OEM Volume Input 3

15523 – OEM Volume Input 4

15524 – OEM Volume Input 5

15525 – OEM Volume Input 6

15530 – Percent Calibrated Volume Input 1

15531 – Percent Calibrated Volume Input 2

15532 – Percent Calibrated Volume Input 3

15533 – Percent Calibrated Volume Input 4

15534 – Percent Calibrated Volume Input 5

15535 – Percent Calibrated Volume Input 6

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, L10G+, Signature 600, ISB 02, ISC 03, ISL 03, ISM 02, ISM 04 and ISX 02 engines.

_____________________________________________________________________________________________________

New in Version 7.1

Added support for the Remote Accelerator Mode parameter to the QSC/QSL 04 DLL. Added support for the J1939 Multiplexing Auxiliary Shutdown Switch to Natural Gas Engines. A problem with the Cummins VCP control panel applet has been fixed.

Natural Gas Engines

- Added support for J1939 Multiplexing Auxiliary Shutdown Switch

QSB / QSC 04

- Added support for Remote Accelerator Mode

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, L10G+, Signature 600, ISB 02, ISC 03, ISL 03, ISM 02, ISM 04 and ISX 02 engines.

_____________________________________________________________________________________________________

New in Version 7.0

The biggest change in this version is the new support for QSC/QSL 04 Multi-Accelerator feature. There were also several enhancements ISBe program. Some VEPS base code bug fixes and enhancement were also completed.

New Engine programs supported:

- QSC/QSL 04

Changes For all Engine Programs

- VEPS will not create a read-only error if the value in the par file matches the value in the ECM.

- When VEPS is run by a user without administration rights, VEPS will still use the VCP settings set by a user with administration rights.

- Allow programming "Minimum AC Fan On Time" even if it is not enabled.

- Wrap dataplate values that don't fit in the defined column width.

- No longer require that gear ratio low is lower than gear ratio high.

All EGR Engine Programs

ISX 02

- Added support for the new Variable Speed Fan Types.

ISB 02

ISC 03 - ISL 03

- Added support for Adaptive Cruise

ISBe

- Use the calibration tool limits on PTP axle torque limit.

- Allow programming PTO and PTP trims even if the feature is disabled.

- Added ECM Part Number, ECM Serial Number, SC option and DO option as read only parameters.

Natural Gas Engines

QSB / QSC

Heavy Duty

Known Issues

- On WIN 98 and WIN ME operating systems, if the VCP configuration option "Write Trace / Debug Information" is selected, it will cause a page fault when VEPS exits.

This setup utility will install all components needed to program ISB, ISC, ISBe, ISL, M11, N14, ISM, ISX, QSB, QSC, QSC 04, QSL 04, QSM, QSX, C8.3G+, B5.9G+, Signature 600, ISB 02, ISC 03, ISL 03, ISM 02, ISM 04 and ISX 02 engines.

Write a review

Please login or register to review

Cummins VEPS VCP 7.70

  • Product Code:
  • Availability: In Stock
  • $150.00